- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Got FIOS recently and the technician at the time of install, set up the wireless connection to the router on my laptop using WEP. I want to change it to the more secure WPA2. I stumbled onto ip address 192.168.1.1, selected "Advanced Security Settings", then "WPA2", then blindly clicked on "apply" with the defaulted settings. Bad move on my part. Now I have no wireless connection with my laptop. How do I undo this, go back to WEP, then have WPA2 applied (or skip the WEP part)? Can some one help with step-by-step instructions???
Solved! Go to Correct Answer
Correct answers
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
So right after the above post, I did the following to finally get a WPA2 connection:
1. When you connect to the router, a window pops up with routers within my vicinity. At the bottom, click on "open network and sharing center"
2. A new window appears. Click on "manage wireless networks" near the top left hand corner.
3. Another window appears which lists "networks you can view, modify, and reorder"
4. Double clicked on my router.
5. Another little window pops up. Choose "security" tab.
6 Select WPA2-Personal for security tupe
7. Leave encryption type as AES
8. Type in your new password (network security key).
9. Click OK
Now it's working!!! Baby steps for computer dummies like me!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Try connecting to your router using an ethernet cable, then login to 192.168.1.1 as you did before.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@Agent99 wrote:Got FIOS recently and the technician at the time of install, set up the wireless connection to the router on my laptop using WEP. I want to change it to the more secure WPA2. I stumbled onto ip address 192.168.1.1, selected "Advanced Security Settings", then "WPA2", then blindly clicked on "apply" with the defaulted settings. Bad move on my part. Now I have no wireless connection with my laptop. How do I undo this, go back to WEP, then have WPA2 applied (or skip the WEP part)? Can some one help with step-by-step instructions???
Push and hold for 10 seconds the reset to factory defaults button on the router.
It will no be back to wep and the keys are on the label on the router.
Login to the router at 192.168.1.1 using user admin and you will be prompted to select a new password. Remember it as it will be the admin password you use in the future.
Select wireles of the the top tabs
select advanced security of the left hand tabs
check the radio button wpa/wpa2
set station security to wpa and wpa2
authentication method pre shared key
type in a key in the preshared key field - use ascii and NOTE down what you enter - this will be the key you are asked for at your wireless devices
select encryption algorith tkip and aes
leave the last line as it was
select apply
If you did all this from a wireless connection (not recommended) you will have to reconnect. This will probably involve you scanning for wireless networks again and selecting FORGET on the router network, then scanning for wireless networks again, selecting the router network at whicxh point you will be prompted for the key - enter the pre shared key you created earlier.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@viafax999 wrote:
@Agent99 wrote:Got FIOS recently and the technician at the time of install, set up the wireless connection to the router on my laptop using WEP. I want to change it to the more secure WPA2. I stumbled onto ip address 192.168.1.1, selected "Advanced Security Settings", then "WPA2", then blindly clicked on "apply" with the defaulted settings. Bad move on my part. Now I have no wireless connection with my laptop. How do I undo this, go back to WEP, then have WPA2 applied (or skip the WEP part)? Can some one help with step-by-step instructions???
Push and hold for 10 seconds the reset to factory defaults button on the router.It will no be back to wep and the keys are on the label on the router.
Login to the router at 192.168.1.1 using user admin and you will be prompted to select a new password. Remember it as it will be the admin password you use in the future.
Select wireles of the the top tabs
select advanced security of the left hand tabs
check the radio button wpa/wpa2
set station security to wpa and wpa2
authentication method pre shared key
type in a key in the preshared key field - use ascii and NOTE down what you enter - this will be the key you are asked for at your wireless devices
select encryption algorith tkip and aes
leave the last line as it was
select apply
If you did all this from a wireless connection (not recommended) you will have to reconnect. This will probably involve you scanning for wireless networks again and selecting FORGET on the router network, then scanning for wireless networks again, selecting the router network at whicxh point you will be prompted for the key - enter the pre shared key you created earlier.
Note do not chose TKIP AND AES. Select AES only. Tkip security turned out to be to easy to break. It is also not supported in WPA2 mode. Don't know about Verizon's routers, but many routers and wireless devices have WPA2 AES code built in to the hardware and will run faster using this security then with any other except open of course.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Okay, I followed the steps with the ethernet cable attached. I then disconnected the ethernet cable, and attempted to connect to the router. When clicking on "connect" to connect to the router, the following error message appeared: "The settings saved on this computer for the network do not match the requirements of the network." Still lost. What do I do next?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
So right after the above post, I did the following to finally get a WPA2 connection:
1. When you connect to the router, a window pops up with routers within my vicinity. At the bottom, click on "open network and sharing center"
2. A new window appears. Click on "manage wireless networks" near the top left hand corner.
3. Another window appears which lists "networks you can view, modify, and reorder"
4. Double clicked on my router.
5. Another little window pops up. Choose "security" tab.
6 Select WPA2-Personal for security tupe
7. Leave encryption type as AES
8. Type in your new password (network security key).
9. Click OK
Now it's working!!! Baby steps for computer dummies like me!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Agent99 wrote: Baby steps for computer dummies like me!
LOL... Which is where many of us started, albeit awhile ago.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
About 20 years ago I was asked, "why did you delete that" my answer was, "because I could". Bad me.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Lol. Reminds me of those moments where I'm asking people why they deleted System32 from their Windows folder. People who were told it fixes problems were like "Well the guy told me to do it, and now my computer won't start!." Otherwise, it was like "I was trying to clean up my Hard Drive, and system32 had a lot of useless files in it!"
😄
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@Smith6612 wrote:Lol. Reminds me of those moments where I'm asking people why they deleted System32 from their Windows folder. People who were told it fixes problems were like "Well the guy told me to do it, and now my computer won't start!." Otherwise, it was like "I was trying to clean up my Hard Drive, and system32 had a lot of useless files in it!"
😄
Yea I was thinking more along the lines of the Digital PDP11-83 with RSX11 Plus. Pre Micro VAX. It was not as easy to delete files back then. No main stream MS Windows. But we were running some special apps on Windows 1.x or 2.x, now that is some history. Getting old and off topic.