Trying to Program Proscan Tv with Remote ....Help
ycurrie
Newbie

I was trying to program P265v 1.1 RC to my Proscan Tv and it wont work, i;ve been using code 302 not working...... Anybody can help??????????/

0 Likes
Re: Trying to Program Proscan Tv with Remote ....Help
Hubrisnxs
Legend

If you've tried the remote code listed for your TV and it did not work, or the remote code is not listed, you can search for a valid code to set up your remote.

Search for a valid code and set up your remote

  1. Turn on your TV and the FiOS TV Set-Top Box.
    Make sure you can see live TV.

  2. Press and hold the OK and FiOS TV buttons together then release both buttons.
    The red LED light blinks 2 times and then stays on.

  3. Press and hold the Play button.
    The remote control tries a new TV code every second.
    The red LED light blinks each time a new code is sent.

  4. When the TV turns off, release the Play button immediately.

    NOTE: Some TVs may respond slower than others. If necessary, you can press the Ch+and Ch- buttons to go forward or backward one TV code at a time.

  5. Test your remote to ensure it is working properly:
    - Turn on the TV by pressing the TV button on your FiOS TV remote.
    - Press the Vol+ and Vol- buttons to ensure that you can control the volume.
    - Press the Mute and A/V buttons to ensure they work.

    If any of these buttons do not work, press and hold that button. Release the button as soon as it works.

  6. If all the buttons work, press OK to this TV remote code.
    The red LED light blinks 3 times and then turns off. Your remote control is now programmed.

That method above may work for you.  Give that a shot.   

0 Likes
Re: Trying to Program Proscan Tv with Remote ....Help
Jeff1212
Newbie

I have a brand new Proscan LED TV and have tried to program my old FiOS remote for it, using both codes and search and a new FiOS remote using both codes and search - neither will program the TV into the remote.  I know the process for each remote and can tell you how to try, but apparently there are NO codes that will work with Proscan.  Can you advise?  Is there a LEARN feature where you can just point one remote at the other and have it learn the codes like other systems?

0 Likes
Re: Trying to Program Proscan Tv with Remote ....Help
dawnib
Newbie

I'm having the same issue with my proscan. I've tried code 302 and then I also found 4 digit codes when using the Fios help option and still no luck.  Any ideas?

0 Likes
Re: Trying to Program Proscan Tv with Remote ....Help
Qckslvr
Newbie
I'm in the same predicament. I just purchased a new Proscan TV for our bedroom, and I can't get the Verizon RC to recognize it. I've tried the direct approach using code 302, and also the auto-search method, and neither worked. Is the problem with Proscan, or Verizon?
0 Likes
Re: Trying to Program Proscan Tv with Remote ....Help
tjg51811
Newbie

I am a new Verizon customer.  I have a Proscan 32" tv that I purchased just before christmas 2012 (so it is new) I do not know the model number off hand.  I have tried to set up the Verizon remote using the code 302 and it did not work.  When I tried to use the code search feature, the tv goes haywire (powering on/off, changing screen colors, and the LED light blinks odd colors.  I have no access to the tv, the remote does not work, I have to manually power off the tv then turn it back on.  Nothing that I do will allow this remote to connect to the tv.  It worked fine with my LG tv in the living room, but nothing works for this tv, and i would love some help!!

0 Likes
Re: Trying to Program Proscan TV with Remote ....Help
danak1
Newbie

I have a Philips RC1445302 remote and had quite a time trying to program the remote to work with the Proscan 39" LED Model# PLDED3996A TV I just purchased for my Dad.  I tried every Proscan, RCA, GE, and Sylvania code to no avail.  The below Verizon manual search instructions will get the job done but there are a couple of quirks.  First, after entering the 922 code wait for the TV button to blink on and off three times before pressing the top of the Play button.  Pressing the Play button causes the TV to turn off for some reason but that is ok, just start pressing the Fast Forward button.  After ~94 clicks the TV will turn on, however this IS NOT the code so don't press the OK button, but continue to press the Fast Forward button until ~120 clicks at which point the TV will turn off with the correct code.  Press the OK button to save the code and you are all set.

Note: These steps only apply to the Philips RC 144 Remote Control.

Searching for a Device Code

    1. Turn on the device you want to program into your remote, for example if you are programming your remote to control your TV, then turn on the TV.
    1. Press and hold the device button for the device you turned on in step 1 (DVD, AUX, TV, STB) and press OK. Release both buttons.

      The mode buttons blink twice.
    1. Press 922.
    1. Point the remote control toward the device you are setting up and press the upper part of the Play button.
    1. Press the Fast Forward button. If the device you are setting up does not turn off, keep pressing the Fast Forward button until the device powers off. (You can use the Rewind button to go back, if necessary.)
  1. When the device powers off then you've found the correct code for that device. Press OK to assign the code in your remote control.
0 Likes
Re: Trying to Program Proscan TV with Remote ....Help
mfizzy
Specialist - Level 1

when using the 302 code, does the TV ever turn off for step 5 of the instruction?

  • Press and release the Ch+ button until the TV turns off. You can also back up by pressing the Ch- button.

    NOTE: Some TVs may respond slower than others to buttons pressed on the remote so wait at least 1 second between button presses.

0 Likes
Re: Trying to Program Proscan Tv with Remote ....Help
chuck19681
Newbie
Anyone ever find a solution to program remote for the proscan? I have tired the code and the search method. I finally got the tv to go off and back on and got the and the mute button to work, but have yet to get the volume to work. I pressed ok to get out of the program mode. only the mute button works... so frustrating. thank you!
0 Likes
Re: Trying to Program Proscan Tv with Remote ....Help
ElizabethS
Moderator Emeritus

As this thread is now over two years old, it will be locked in order to keep discussions current. If you have the same or a similar question/issue we invite you to start a new thread on the topic.

0 Likes