Accessibility Resource Center Skip to main content
Get it fast with In-Store & Curbside Pickup or same day delivery.

9100EM and WRE54G

Reply
peta8368
Contributor
Contributor
Posts: 2
Registered: ‎09-03-2009

9100EM and WRE54G

Message 1 of 4
(6,188 Views)

I have the westell 9100EM modem/router, and bought a linksys wre54g to try to increase the range. However, I simply cannot get the wre54g to work. If i use the setup CD, it always fails with the message "cannot associate with this ap in repeater mode". I also tried to do it manually by going to 192.168.1.240. The default gateway shows 0.0.0.0 when I reset. Everytime I set it to 192.168.1.1 and save the setting, 240 drops off the network. If i leave that alone, and put my wireless network's information in, the device also drops off the network. Has anyone had any experience with it? Any walkthrough or tips would be greatly appreciated. Thank you.

 

 

Peter

3 REPLIES 3
VZ_JoeD
Employee Emeritus Employee Emeritus
Employee Emeritus
Posts: 171
Registered: ‎07-10-2009

Re: 9100EM and WRE54G

Message 2 of 4
(6,168 Views)

Change wre54g to 192.168.1.50 instead of the defaulted range .240 and let me know if that helps.  If not 

 

 1. reset the unit (push the reset button for 30 seconds with a large paper clip) 2. plug the WRE54G into a wall socket but do not connect it to the network with a network cable. 3. Use the CD software. 4. If the software finds your existing network that you want to connect to, say yes. If it finds the WRE only say no and try again. Eventually after several cycles like this it will find both. (If not reset the WRE again and try again). 5. Eventually you will have chosen your existing network and it will have found the WRE (with the very long default name). 6. Select MANUAL setup. 7. Give the WRE the same SSID as the existing network. 8. Give the WRE the same security method (WEP for example) and the passphrase you used for the existing network. 9. finally there will be this box that counts to 100% and then dissappears. Wait awhile. Sometimes nothing happens for 5 minutes. If and when the "Congratulations" box shows up and the two lights on the WRE are blue you are all set. If this does not come up you may have to reset the WRE and try again.

Joe D
Verizon Telecom
Fiber Solution Center


Notice: Content posted by Verizon employees is meant to be informational and does not supercede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.Follow us on Twitter™!

peta8368
Contributor
Contributor
Posts: 2
Registered: ‎09-03-2009

Re: 9100EM and WRE54G

Message 3 of 4
(6,149 Views)

My LAN is using 192.168.1.x, and the 9100em is on 192.168.1.1.

 

should I still change the wre54g to 192.168.0.x?

dslr595148
Trivia Champ
Trivia Champ
Posts: 6,062
Registered: ‎09-24-2008

Re: 9100EM and WRE54G

Message 4 of 4
(6,128 Views)

Yes, please do..

If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.


 

How-To Videos
 
The following videos were produced by users like you!
   
Videos are subject to the Verizon Fios Community Terms of Service and User Guidelines and contains content that is not created by Verizon.
Have a spare Fios-G1100?Learn how to bridge it into your network
Get Started


Covid19

Browse Categories
Categories:
Posts

Verizon Troubleshooters
Unable to find your answer here? Try searching Verizon Troubleshooters for more options.
Modal Dialogue Title