Accessibility Resource Center Skip to main content
Get it fast with In-Store & Curbside Pickup or same day delivery.

Connecting MOCA Adapter through a switch to feed STB data?

SOLVED
Reply
NOVArunner
Contributor
Contributor
Posts: 1
Registered: ‎08-16-2020

Connecting MOCA Adapter through a switch to feed STB data?

Message 1 of 3
(1,125 Views)

Recently moved my G3100 router from basement utility closet (where both MOCA and Ethernet connections to OTN terminate) to kitchen on main floor of 3 story house to be more centrally located and get better WiFi on rear deck. Kitchen was already wired with duplex Ethernet jacks allowing me to connect Ethernet to G3100 and use 2nd jack to connect to an unmanaged switch in basement feeding 3 wired PCs.

Problem is that there is no Coax wiring in the kitchen and no easy means to bring it there to connect to the G3100 (I have a long cable across the floor from another room temporarily). Based on comments from people using their own routers, hoping I can install a MOCA to Ethernet adapter and connect this to the switch in the basement. Will this setup work, or does the MOCA adapter need to be connected directly to the G3100? Not sure it makes a difference, but there are two separate MOCA drops from the ONT (one for router and one to splitter feeding each STB).HomeNetwork.jpg

1 ACCEPTED SOLUTION

Accepted Solutions
appDev
Bronze Contributor II
Bronze Contributor II
Posts: 72
Registered: ‎07-27-2020

Re: Connecting MOCA Adapter through a switch to feed STB data?

Message 3 of 3
(1,022 Views)

Taking another look, i think it could be even simpler - the Moca from the network switch simply needs to to the Coax Splitter to the STBs. No need to go back to the ONT - in fact, it might be counterproductive.

 

Also, remember to install a PoE filter (example - https://www.amazon.com/Filter-MoCA-Cable-Coaxial-Networking/dp/B00DC8IEE6) where the coax comes into the house - between the ONT and splitter.

View solution in original post

2 REPLIES 2
appDev
Bronze Contributor II
Bronze Contributor II
Posts: 72
Registered: ‎07-27-2020

Re: Connecting MOCA Adapter through a switch to feed STB data?

Message 2 of 3
(1,082 Views)

Your setup should absolutely work. I currently have (a slightly shorter version of) the same setup - ONT -> my own router -> switch -> Moca -> STB.

 

I am using my older G1100 as a moca bridge (since i already have it), but also waiting for delivery on moca adapters, but what you are thinking of will work.

appDev
Bronze Contributor II
Bronze Contributor II
Posts: 72
Registered: ‎07-27-2020

Re: Connecting MOCA Adapter through a switch to feed STB data?

Message 3 of 3
(1,023 Views)

Taking another look, i think it could be even simpler - the Moca from the network switch simply needs to to the Coax Splitter to the STBs. No need to go back to the ONT - in fact, it might be counterproductive.

 

Also, remember to install a PoE filter (example - https://www.amazon.com/Filter-MoCA-Cable-Coaxial-Networking/dp/B00DC8IEE6) where the coax comes into the house - between the ONT and splitter.

View solution in original post

How-To Videos
 
The following videos were produced by users like you!
   
Videos are subject to the Verizon Fios Community Terms of Service and User Guidelines and contains content that is not created by Verizon.
Have a spare Fios-G1100?Learn how to bridge it into your network
Get Started


Covid19

Browse Categories
Categories:
Posts

Verizon Troubleshooters
Unable to find your answer here? Try searching Verizon Troubleshooters for more options.