- « Previous
-
- 1
- 2
- Next »
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Regarding the tar file with the source code. Does anyone know how you can compile it to flash the G1100? I see that if you uncompress all the folders you have a bunch of folders with code. Some you can run make on, but others you can't. So, what do you make it a firmware file for upload to the router?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
My FiOS G1100 router has:
Firmware Version
02.00.01.08 |
I see on the Open SOurce page
Does any have instructions on how to apply the .tar file to the G1100 router?
EDIT: I found this link http://192.168.1.1/#/advanced/fwupgrade gets you to the right place. Now I just need the right FW file for 2.10.07
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
swieder - have you found the answer?
And is 2.00.010.07 noticeably better than 02.00.01.08?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Nope it is the other way around. Frontire firmware is flashed on FIOS gateway
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@swieder wrote:My FiOS G1100 router has:
Firmware Version
02.00.01.08 I see on the Open SOurce page
Does any have instructions on how to apply the .tar file to the G1100 router?
EDIT: I found this link http://192.168.1.1/#/advanced/fwupgrade gets you to the right place. Now I just need the right FW file for 2.10.07
did u find how to apply the TAR file??
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
nm ... i see it mentioned here that the tarball is the source and needs compilation suitable for upload/flash... will continue searching for instructions to convert tarball to flashable bin ...
--orig q below ... duplicate.
this is my hardware.
UI Version: v1.0.294
Firmware Version: 02.00.01.08
Model Name: FiOS-G1100
Hardware Version: 1.03
and i am trying to update the router firmware using
https://www.verizon.com/cs/groups/public/documents/adacct/bhr4_release_02_02_00_14.tar
the ok button to upload does not appear to be functional after selecting the tarball
on this page http://192.168.1.1/#/advanced/fwupgrade
Do i have to extract the tarball and upload individual files. Seems to many....
thank you in advance for any pointers.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
There is no ability for a user to flash Verizon routers. All firmware updates are pushed from the Verizon infrastructure. Even if you could build an image, you can't load it.
Further, you can't build an image. The publicly available code is the open source code in the router. There most likely is proprietary code in the image as well, such as for the various network hardware blocks. Any proprietary code isn't in the tarball. I suspect there are security certificates in the image used for TR-069 and similar. The SoC may also use a secure boot process, which means the image needs to be digitally signed. If you don't have the public key for the digital signature, you can't make a bootable image. I doubt Verizon makes the public key, well, public.
I could be wrong about this, but from what I've seen the publicly available code is missing a lot of pieces. If you're able to figure out how to build an image and flash it without going through Verizon's servers you'll be the darling of the router hacking world.
Good Luck.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
As this thread is now over two years old, it will be locked in order to keep discussions current. If you have the same or a similar question/issue we invite you to start a new thread on the topic.
- « Previous
-
- 1
- 2
- Next »