|This is the last time your account was accessed.|
05-10-2012 01:36 PM
Since upgrading to FIOS internet a year ago, I have been unable to connect to the Steam Client. I have been in contact with Steam support and after months of trying all thier suggestions, I am still unable to connect. I keep getting the message that "Steam is having trouble connecting to the Stream servers". I am currently using the Actiontec router, but I have also tried the Westell and it also failed.
I have used a program called PFConfig to set the correct port forwarding in the router (I verifed that it is correct). At Steams request, I disabled all non Microsoft services and uninstalled Norton Internet Security and was still unable to connect. I have tried using 3 different PC's. One with the Vista OS and two with Win 7. I am in the southern California area.
I am at wits end. If I cannot correct this issue, I will not be able to install any game which uses Steam as the DRM.
Anyone have a suggestion?
05-10-2012 01:58 PM
Delete the port forwarding. Pick a PC, determine the IP address it presently has been assigned and place that address in the DMZ on the router and try it. If that works, then you have the port forwarding wrong ... if it doesn't, then there's something goofy with your PC firewall configuration most likely.
05-11-2012 05:41 AM
Steam doesn't require any special kind of Port Forwarding. As long as the requests Steam makes does not get blocked by a Firewall (perhaps the one in the router is a consideration, too. DMZ should get around that but it should not be needed), it works just fine. Back in the day when Steam was first made it did use Port Forwarding as it operated on a Peer-to-Peer basis, however they now use HTTP-based CDNs instead.
So certainly investigate your PC and Router Firewall. Bet ya one of them is blocking the Steam client from connecting properly.
05-11-2012 07:03 AM
One way to determine is by doing a wire shark session. Start it on Computer A by run wireshark on a Different computer but put a filter in for Src and Dest address as Computer A. This will help limit it down if it is a router problem or a PC problem.
05-11-2012 08:16 AM
Just a point of clarification to the last post ... since most wired networks, including the ActionTec, are "switched" networks, a Wireshark won't show the traffic if run from a different system, it would have to be running on the system from which you initiate the session to see the traffic.
The DMZ suggestion I made previously is the quickest way of ruling out the router as the cause. I wouldn't recommend it long term, but it will help focus where you need to be looking for the problem -- router or PC.
05-11-2012 09:31 AM - edited 05-11-2012 09:35 AM
It should be noted however that Steam currently does not support operation through a network DMZ. Quoting a steam tech support email: "If your machine is currently in a network DMZ, you will need to reconfigure your network to play through Steam."
He may need to portforward. I would recommend using www.simpleportforwarding.com
it worked for me
Typically, Gaming needs Steam and the only inhibitor is not the outbound, but rather the failure to port forward
to the gamingsystem's ip address (obviously it must be a static LAN address)
05-11-2012 11:57 AM
As I said in my original post, I have used a utility called PFConfig to set the required port forwarding in the router as directed by Steam support. I have browsed into the route to insure they are correct. It has made no difference. I have tried to connect on three different PC's, 1 Win Vista and two Win 7. I get the same error on all three.
I have been through months of work with Steam support. As I said above, they had me set the port forwarding, they had me disable all services other than microsoft and uninstall Norton Internet Security. After doing all that, I still could not connect. I am beginning to suspect there is something inherent in the Actiontec router or FIOS in So Cal that is causing this problem.
05-11-2012 12:20 PM
Steam does not support DMZ. From the Steam support site:
Steam does not support gameplay on machines operating in a network DMZ. You must remove your machine from the DMZ in order to play through Steam.
05-11-2012 02:12 PM - edited 05-11-2012 02:14 PM
well definetely not something regional, I am in so cal and it works fine for me.
I know that I used the one that I mentioned, I didn't use pfconfig and it worked for me. So I also have an actiontec, and this is a national message board, so if it was something wrong with the actiontec in general, it would be more of an issue, but we don't see them very often here.
Do you have a second router? maybe you can piggy back it to the actiontec and it would work with the settings from the new router?
BEFORE DOING ANY OF THAT
I would recommend looking at this page, there are a lot of common problems and fixes for portforwarding in here, that a lot of people don't realize.
maybe one of them will be a golden goose for you?
05-11-2012 03:03 PM - edited 05-11-2012 03:06 PM
Is this the port forwarding info you used : https://support.steampowered.com/kb_article.php?re
I used to turn off my router firewall to connect, once I set up port forwarding I could use Typical security setting on the router firewall and Steam worked fine. I would never turn off or disable my AV, if that is truly needed switch to Microsoft Security Essentials. Note I am still on DSL and will be going to FIOS next week so I am interested in how this turns out.
If you want to try an alternate account PM me, have a "dummy account' that you can use.